How To Transform a Tie-Dyed T-Shirt into a Long Skirt

I've been cutting up clothes for quite a few years now making them into something different, so when I went through my stash of tie-dyed t-shirts and found this baby sitting amongst them all, I decided to try something new.

First of all, how could I possibly cut up the peace sign? Nuttin' doin'. Couldn't happen. So, for the first time I had to figure out a way to make this skirt-to-be longer than the ones I'd done previously when cutting them under the armpits and folding the top over for an elastic waistband. Somehow I had to use the whole shirt without the neckband and sleeves as part of the skirt.

I loved the bottom of the t-shirt and knew I wanted to use that as the bottom of the skirt, so there was going to be no shortening the length on this baby. I wanted it all, so I cut off the sleeves and the neckband to see what I had left to work with. One thing was for sure the yellow sleeve that I had just removed would look really great as a small waistband, and if I used 1/4" seam allowance I knew I wouldn't chop off any of the peace sign.

I used rotary cutting tools to help get a straight cuts on the sides and now the new waistline. Ta da! I cut the front and back together, and then was ready to strap on that waistband that I cut from the one sleeve. I used a 2" width by the length of the waistband.

What I decided to do so the 1/2" wide elastic wouldn't roll in the waistband after it was sewn was to cut it into two pieces -- one for the front and one for the back. Therefore, I had to cut a front waistband and then a back waistband. I normally don't do it this way, but thought it would be better in the long run for this fit.

I cut out a strip 2" wide x 20 1/2" long (the length of the top of the skirt), sewed the strip right sides together with the top of the skirt. Then I folded it in half, wrong sides together and sewed it along the same seam line as the previous one. This created a waistband where I could insert the 1/2" wide elastic.

So, what you see in the above photograph is what the waistband looks like on the front side after sewing it to the skirt and after threading the elastic through the side seam. I pin the elastic in place so that it doesn't slip through.

I sewed the back as I did the front, and then when both are done, I pinned the side seams from the waistband to 8" above the hemline. You should pin them right sides together, but as you'll notice from the photos the back of mine is wrong side out. I left it that way. Apparently, I'm not planning on selling this one!

The reason for clipping the seam is so that I was then able to turn under the seam allowance below the clip all the way to the hemline. I turned in the seam 1/4" and then another 1/4" so no raw edge is showing. This gives me plenty of room to walk or sit while wearing the skirt and it's not prohibitively narrow around the knees. Sometimes a seam will break if there's no walking room in the width of the skirt.

The last thing to do was to stitch close to the turned under edge of the seam allowance, sewing across the other side below the clipped seam, cutting any long threads, and then put it on and wear it with pleasure!

This is the first of many of these skirts that I plan on making. I feel so very fortunate to be able to have the selection of tie-dyed t-shirts from my partner, Dan. His tie-dyes are just exceptional!

I also wore this as a dress with the "waistband" under my armpits. It made for a great swimsuit cover-up!

Also, if you're sewing on a regular sewing machine, not a serger, with these knits, I highly recommend using a ball point needle and stretching the fabric while you sew, especially the waistband. Otherwise, your stitches will pop when you stretch the skirt over your hips. Just sayin' -- been there, done that, my friends! Now, happy sewing and thanks for stopping by!